Denon CDR-WI500 Instruções de Operação descarregar pdf (Página 7)

ENGLISH

Precautions When Loading Discs

• Only load one disc. Loading two or more discs in a layer will

cause breakdown and may also scratch the discs.

• Discs of the 8 cm size should be carefully aligned with the

recessed disc guide area and loaded without the use of an

adapter. If not properly loaded, the disc may fall out or the

disc holder may cease to open.

• Be careful not to get your finger caught when the disc

holder is closing.

RESTRICTIONS RELATED TO THE CD-R/RW STANDARDS

★ Standards concerned with CD recorder playback have been established based on the existing standards of CD players;

however, for recording, the method differs from that used with existing cassette decks and MD recorders, etc. In view of this,

please gain a good understanding of the following restrictions associated with CD-R/RW discs and enjoy the medium.

Restrictions of Audio CD-R/RW Discs

• Only audio CD-R/RW discs can be recorded with this unit. “Use Audio CD” will be displayed when a disc other than one

for use with audio such as a CD-R/RW disc for use with a personal computer or another type of disc is loaded. (See “Discs that

Can Be Used with this Unit” on Page 5.)

• CD-R discs can be recorded to only once. The recorded information cannot be erased.

• The recorded information of CD-RW discs can be erased. When this disc has been finalized, erase after the finalization removal

operation has been performed. (See “Cancellation of CD-RW disc finalizing” on Page 28.)

• Recording mistakes made with CD-R discs cannot be erased; therefore, it is recommended that a CD-RW disc be used until you

are accustomed to the recording operation.

Restrictions in Recording with this Unit

• The recording operation procedure is the same for CD-R discs and CD-RW discs.

• When making additional recording to a previously recorded disc, the end of the last track is detected and recording is started

from there.

• The record standby mode cannot be set for CD-R/RW discs with a recordable time of about 8 seconds or less remaining.

“Disc Full” will be displayed at this time.

• A maximum of 99 tracks can be recorded to one CD-R/RW disc. When the recording reaches the 99th track, “Disc Full” is

displayed and recordings beyond this track will not be possible.

• Digital recording is not possible from CD-R/RW discs onto which have been digitally recorded, normal is it possible from MD or

DAT, etc. When a digital recording is attempted from such sources, “Copy Prohibit” is displayed. To record from these

digital sources, make the recording from the analog input. (See “Digital Copies” on Page 6.)

• This unit cannot record CD-ROM and other non-audio signal sources. When an attempt is made to record from such sources,

“Copy Prohibit” is displayed.

• When a recording is made from a disc that includes data other than audio signals such as CD graphics or CD-TEXT, only the

audio signal is recorded; other data is not recorded.

• DVD (Dolby Digital, DTS, and other compressed audio signals) cannot be recorded.

Compatibility with Other CD Players and Discs

• Finalization processing on a CD-R disc that has been recorded with this unit will permit that disc to be played on ordinary CD

player. (See “Finalizing CD-R/RW Disc” on Page 27.)

•

Finalization processing on a CD-RW disc that has been recorded with this unit will permit that disc to be played only on a CD player

designed to be used with CD-RW discs or on another CD recorder. (See “Finalization Processing of CD-RW Discs” on Page 6.)

• Do not place anything other than a disc on the disc tray.

• Do not use discs that are cracked, misshapen, or have been

repaired with an adhesive, etc.

• Do not use discs that have adhesive coming out from

cellophane tape or the label of a rental disc, or adhesive

remaining after removal of the label. Use of a disc in this

condition may result in the disc not being ejected or in

breakdown.

CONNECTIONS

(1) Analog Input/Output Jack Connections

• Use the supplied pin plug cable when

making connections with the analog

input/output jacks.

q Input:

Connect the analog input jacks (ANALOG

IN) of this unit with the output jacks of

the amplifier (MD or TAPE).

w Output:

Connect the analog output jacks

(ANALOG OUT) of this unit with the

input jacks of the amplifier (MD or TAPE).

e CD-only output:

Only the CD side sound is output.

Connect to the amplifier’s input jacks

(CD, etc.).

✽ In the dual mode, only the sound of

the CD-R side is output from the

CD/CD-R output jacks, so this

connection is required.

• Please use optical fiber cables, which is

available on the market, when making

connections to the digital (OPTICAL)

input/output jacks.

Use 75Ω/ohms pin plug cable, which is

available on the market, when making

connections to the digital (COAXIAL)

input/output jacks.

q Input:

Connections with Playback Equipment

such as the CD Players

The digital input jacks of this unit (either

DIGITAL IN OPTICAL or DIGITAL IN

COAXIAL) should be connected with the

digital output jacks of the CD player

(OPTICAL or COAXIAL).

w Output:

Connections with Equipment having a

Digital Input such as the MD Recorder

The digital output jacks of this unit (either

DIGITAL OUT OPTICAL or DIGITAL OUT

COAXIAL) should be connected with the

digital input jacks of the MD recorder or

other equipment (OPTICAL or COAXIAL).

e CD-only output:

Only the CD side sound is output.

Connect to the digital input jacks of an

MD recorder, etc.

(2) Connection of Digital Input/Output Jacks

NOTES:

• Do not plug the power plug into the power outlet until all connections have been completed.

• Connect the red plug of the pin plug cable into the R (right) jack and the white plug into the L (left) jack.

• Do not make a connection to the PHONO jack of the amplifier. Doing so will lead to breakdown.

• Firmly plug in the power plug. An imperfect connection will cause noise to be generated.

• Bundling the connection cables together with the power cable will cause hum or other noise.

• When the power plug is disconnected from the power outlet, wait about 5 seconds before reinserting.

SPEAKER SYSTEMS

TAPE-1

/MD

TAPE-2

/DAT

REC

TAPE-1

/MD

TAPE-2

/DAT

PHONO CD TUNER AUX

SIGNAL

GND

INPUTS

CDR

ANALOG

CDR

DIGITAL IN DIGITAL OUT

COAXIAL

OPTICAL

CD/CD-R

COAXIAL

OPTICAL

COAXIAL

OPTICAL

OUT OUT

CD/

CDR

ANALOG

CDR

DIGITAL IN DIGITAL OUT

COAXIAL

OPTICAL

CD/CD-R

COAXIAL

OPTICAL

COAXIAL

OPTICAL

OUT OUT

CD/

COAXIAL OPTICAL

OUT OUT

DIGITALLINE OUT

DIGITAL

OUT IN IN IN

OPTICAL COAXIAL OPTICAL-1 OPTICAL-2

ANALOG

OUT IN

Amplifier

CDR-W1500

Power

Supply

outlet

Power

Supply

outlet

120 V

60 Hz

120 V

60 Hz

120 V

60 Hz

Power Supply outlet

MD recorder

CD player

NOTES:

• To assure accurate recording, record with an ambient temperature of 30 °C or less.

• Do not obstruct the ventilation holes on the top.

• Recording may stop if the unit is subject to shocks during recording. If recording stops, it may no longer be possible to

use the disc normally.

1 2 3 4 5 6 7 8 9 10 11 12 ... 97 98

Comentários a estes Manuais

Sem comentários

Denon CDR-WI500 Instruções de Operação Página 7

Comentários a estes Manuais

Manuais e produtos relacionados com Equipamento de gravação Denon CDR-WI500